CCNP Security : FIREWALL 課程(可考取 Cisco FIREWALL Security Specialist 和 Cisco ASA Specialist認證)

合格保障：學員若考試不合格，本中心均會代付考試費，令學員可免費重考！詳情...

Cisco Systems Inc. 是全球最大的網路設備生產商，在世界各地設有 120 個以上的分支據點。Cisco 的產品包括 Switch (交換器)、LAN Router (區域網路由器)、WAN Router (廣域網路由器)、IOS (Internetwork Operating System) 網路管理操作系統、ASA (Adaptive Security Appliances)、IPS (Intrusion Prevention System) 等。全球的大企業、銀行、大學和政府機構之網路設備，無一不採用 Cisco 的產品，管理 Cisco 網路設備便成為一門專業的學問。

為了能證明你有專業水準來安裝、設定及管理 Cisco 的網路安全產品，Cisco 便推出其 CCNP Security (Cisco Certified Network Professional - Security，Cisco 認可網路安全專業人仕) 國際認可考試。要考取 CCNP Security 國際認可證書，必須通過以下 4 科的考試及持有有效的 CCNA Security 證書：

• CCNP Security: SECURE (Securing Networks with Cisco Routers and Switches) - 642-637
• CCNP Security: FIREWALL (Deploying Cisco ASA Firewall Solutions) - 642-617
• CCNP Security: VPN (Deploying Cisco ASA VPN Solutions) - 642-647
• CCNP Security: IPS (Implementing Cisco Intrusion Prevention System) - 642-627

此外，為了能證明你有專業水準來安裝、設定及管理Cisco的防火牆產品 (IOS Firewall and ASA)，Cisco 便推出其 Cisco FIREWALL Security Specialist (Cisco 認可防火牆專業人仕) 國際認可考試。要考取 Cisco FIREWALL Security Specialist 國際認可證書，只須通過以下 2 科的考試及持有有效的 CCNA Security 證書：

• CCNP Security: SECURE (Securing Networks with Cisco Routers and Switches) - 642-637
• CCNP Security: FIREWALL (Deploying Cisco ASA Firewall Solutions) - 642-617

此外，為了能證明你有專業水準來安裝、設定及管理 Cisco 的 ASA 產品，Cisco 便推出其 Cisco ASA Specialist (Cisco Adaptive Security Appliances Specialist，Cisco 認可 ASA 專業人仕) 國際認可考試。要考取 Cisco ASA Specialist 國際認可證書，只須通過以下 2 科的考試及持有有效的 CCNA Security 證書：

• CCNP Security: FIREWALL (Deploying Cisco ASA Firewall Solutions) - 642-617
• CCNP Security: VPN (Deploying Cisco ASA VPN Solutions) - 642-647

本課程只教授 CCNP Security: FIREWALL (Deploying Cisco ASA Firewall Solutions) - 642-617

本中心的 CCNP Security: FIREWALL 課程由 Franco Tsang (擁有 CCIE : Security, CCIE : Service Provider 及 CCIE : Routing and Switching 三項 CCIE 證書) 籌備多時，精心編排。由上堂、溫習、實習、考試研習、做試題至最後考試，均為你度身訂造，作出有系統的編排。務求真正教識你，又令你考試及格。

本中心為 Cisco 指定的 CCNP Security: FIREWALL 考試試場，報考時請致電本中心，登記欲報考之科目考試編號、考試日期及時間 (最快可即日報考)。

臨考試前要繳付考試費 HK$1,565，及必須出示下列兩項有效之身份證明文件，否則考生不可進行考試，而已繳付之考試費亦不會退回：
1. 香港身份證 及
2. 附有考生姓名及簽名的證件 (如信用咭、香港特區護照、BNO等)

考試題目由澳洲考試中心傳送到你要應考的電腦，考試時以電腦作答。所有考試題目均為英文，而大多數的考試題目為單項選擇題 (意即 O) 或多項選擇題 (意即 口)，其餘則為配對題及實戰題。作答完成後會立即出現你的分數，結果即考即知！考試不合格便可重新報考，不限次數。欲知道作答時間、題目總數、合格分數等詳細考試資料，可瀏覽本中心網頁 "各科考試分數資料"。

為進一步加強本中心 Cisco 的課程質素，本中心投放大量資源購買 Cisco 器材，以供學員進行實習。以下是本中心擁有的 Cisco 器材 (種類繁多，未能盡錄)：

課堂由導師以講座形式教授課程理論及進行眾多的商業實習，而實習時段由學員親自進行商業實習。

FIREWALL:

1 Introduction of ASA
1.1 Configuration File Management

2 Configure ASA Interfaces
2.1 Security Level Overview
2.2 實習: Configure hostname and “inside” interface with static IP address 10.0.0.15/8.
2.3 實習: Configure “outside” interface with DHCP client feature.
2.4 實習: Configure IPv6 on the ASA.
2.5 實習: Configure “outside” interface with PPPoE client feature.
2.6 DHCP Server
2.7 實習: Configure DHCP Server
2.8 實習: Study the meaning of security-level

3 ASA Management Access Configuration
3.1 Enable Password
3.2 實習: Configure Enable password
3.3 Telnet Access
3.4 實習: Configure telnet access in ASA - part 1
3.5 實習: Configure telnet access in ASA - part 2
3.6 SSH (Secure Shell) Access
3.7 實習: Configure SSH Access in ASA
3.8 ASDM (Adaptive Security Device Manager)
3.9 實習: Configure ASDM

4 System Monitoring in ASA
4.1 實習: Configure NTP Client with authentication in ASA
4.2 System Message Severity Levels
4.3 實習: Enable and Configure General Properties of System Logging
4.4 實習: Enable Console Logging
4.5 Terminal Logging:
4.6 實習: Termial Logging
4.7 實習: Configure Syslog
4.8 實習: Configure SNMP Trap
4.9 實習: Configure SNMP GET
4.10 實習: ASDM Logging
4.11 實習: Buffer Logging
4.12 實習: Buffer Logging – Manual Flash Logging
4.13 實習: Buffer Logging – Automatic Flash Logging
4.14 實習: Buffer Logging – Automatic save log to FTP
4.15 Advanced ASA Logging

5 IP and IP Multicast Routing in ASA
5.1 Basic Routing Concepts
5.2 Static Routing
5.3 實習: ASA Static Routing
5.4 實習: Simple Load Balancing by Static Routes
5.5 Service Level Agreement (SLA) in ASA
5.6 實習: Static Routing with SLA
5.7 RIP
5.8 實習: RIPv1 in ASA
5.9 實習: RIPv2 in ASA
5.10 實習: default gateway advertisement by RIP in ASA
5.11 實習: RIPv1 and RIPv2 coexist in ASA
5.12 實習: RIP plain text authentication in ASA
5.13 實習: RIP MD5 authentication in ASA
5.14 OSPF (Open Shortest Path First)
5.15 實習: Single Area OSPF
5.16 實習: Multi-Area OSPF
5.17 實習: Advertise default gateway via OSPF in ASA
5.18 Special OSPF Network Type in ASA
5.19 實習:OSPF Point-to-Point Non-Broadcast network type in ASA
5.20 Virtual Link
5.21 實習: Virtual Link in ASA
5.22 OSPF Authentication
5.23 實習: OSPF Plain Text authentication.
5.24 實習: OSPF MD5 authentication.
5.25 EIGRP
5.26 實習: Configure EIGRP in ASA
5.27 EIGRP Authentication
5.28 實習: Enable EIGRP Authentication in ASA
5.29 IP Multicast in ASA
5.30 實習: Multicast in ASA

6 Network Access Control
6.1 Access List Types
6.2 Access Control Entry Order
6.3 Extended Access List
6.4 實習: Basic Extended Access List
6.5 實習: Add an ACE to an existing Extended Access List
6.6 Standard Access List
6.7 實習: Basic Redistribution between OSPF and EIGRP in ASA
6.8 實習: Using Standard Access List to perform route filtering in ASA
6.9 IPv6 Access List
6.10 實習: Configure IPv6 Access List
6.11 Advanced Access Control List Topics
6.12 Object Grouping
6.12.1 Object Grouping: Protocol
6.12.2 Object Grouping: Network
6.12.3 Object Grouping: Service
6.12.4 Object Grouping: ICMP Type
6.13 實習: ACL with object grouping
6.14 Time-based ACL
6.15 實習: Time-Base ACL
6.16 ICMP Filtering
6.17 實習: Configure ICMP Access in ASA
6.18 Application Layer Filtering
6.18.1 Content Filtering
6.19 實習: Filter Java in ASA
6.20 URL Filtering

7 Packet Monitoring in ASA
7.1 實習: Capture all traffic in the outside interface.
7.2 實習: Monitor the connection by “show conn”.
7.3 實習: Trace a packet by “packet-tracer”

8 NAT (Network Address Translation)
8.1 Basic NAT Concepts
8.1.1 Dynamic NAT Concept
8.2 Dynamic NAT with overload Concept
8.3 Static NAT Concept
8.4 實習: Configure Static NAT
8.5 實習: Static NAT with PAT
8.6 實習: Dynamic NAT with overload.
8.7 實習: Dynamic NAT with public ip pool
8.8 實習: Dynamic NAT with public ip pool with interface ip address for last resort
8.9 Advance NAT Topics – Twice NAT
8.10 實習: Twice NAT 1
8.11 實習: Twice NAT 2
8.12 實習: Twice NAT 3
8.13 DNS and NAT.
8.14 實習: NAT with DNS 1
8.15 實習: NAT with DNS 2

9 AAA (Authentication, Authorization, Accounting)
9.1 AAA Components
9.2 AAA Protocols
9.3 實習: Local AAA for telnet authentication
9.4 實習: Local AAA for SSH authentication
9.5 實習: Local AAA for ASDM authentication
9.6 實習: Local AAA for Console authentication
9.7 實習: Local AAA for Enable authentication
9.8 實習: AAA authentication for telnet authentication by using Cisco ACS
9.9 實習: AAA authentication for SSH authentication by using Cisco ACS
9.10 實習: AAA authentication for ASDM authentication by using Cisco ACS
9.11 Advanced AAA Topics – Cut Through Proxy
9.12 實習: Cut-Through Proxy

10 Modular Policy Framework
10.1 Features provided by Modular Policy Framework
10.2 Default Modular Policy Framework
10.3 Default Inspection: DNS
10.4 Default Inspection: FTP
10.5 Default Inspection: ESMTP and SMTP
10.6 Default Inspection:TFTP
10.7 Default Inspection: H.323
10.8 實習: Layer 3 / 4 Inspection
10.9 Inspection Policy-Map
10.10 HTTP Deep Inspection
10.11 實習: HTTP Inspection – Blocking specific request method.
10.12 實習: HTTP Inspection – Block specific URL
10.13 實習: HTTP Inspection – Block specific browser.
10.14 實習: HTTP Inspection – Block specific Content Type
10.15 實習: HTTP Inspection – Block specific Content
10.16 實習: FTP Deep Inspection – Block FTP commands

11 Transparent Firewall
11.1 Routed Mode
11.2 Transparent Mode
11.3 實習: Configure Transparent Firewall
11.4 Ethertype Access List
11.5 Demonstration: EtherType Access List

12 High End ASA Initialization
12.1 Demonstration: Initialize High End ASA
12.2 Management Interface
12.3 Demonstration: Management Interface
12.4 Subinterface (Trunking) in ASA
12.5 Demonstration: ASA Subinterface

13 Multiple Contexts
13.1 Basic Concept of Multiple Context
13.2 Moment to use Multiple Context
13.3 Limitation of Multiple Contexts.
13.4 Configuration Logic in Multiple Contexts
13.5 Admin Context
13.6 Classifier
13.7 Demonstration: Change from Single mode to Multiple Mode.
13.8 Demonstration: Configure interfaces, create contexts and assign interfaces to contexts
13.9 Demonstration: Configure admin context
13.10 Demonstration: Configure custom context franco1
13.11 Demonstration: Configure custom context franco2

14 Failover
14.1 Introduction of Failover
14.2 Hardware Requirements
14.3 Software Requirements
14.4 Failover Link
14.5 Failover Behaviour
14.6 Demonstration: Active / Standby Failover
14.7 Active / Active Failover
14.8 Demonstration: Active / Active Failover

15 Appendix – HTTP inspection by ASDM